- #Networx security command center power down how to#
- #Networx security command center power down code#
Its function, versatility, and ease of operation make it ideal for home or office use. Control of your security system is achieved through the Command Center, which offers a variety of basic and advanced features. Each of these devices is connected to a sophisticated control panel with microprocessor, which processes all events registered by the system. It consists of one or more Command Centers, motion sensors (for example, detectors or devices located on doors and windows) and sensing devices designed to detect the presence of smoke or combustion. Introduction Your system helps to secure life, property, and investments against fire, theft and bodily harm. Certain functions covered may require you to enter your personal passcode. Some of them may not be enabled in your system. The functions described in this guide are programmed by your security company. It covers basic functions, such as turning the system on and off.
#Networx security command center power down how to#
9 Command Center LED Descriptions Commands System Events Fire Alarms Burglary Alarms Fire Trouble Events Non-Fire Trouble Events How Your System Reports Alarms Silence Alarms Keypad Adjust (Cmd 49) Log Out of the System Turn the System Off Turn the System All On (All On or Cmd 1) Turn the System Part On (Part On or Cmd 2) Turn the System Part 2 On (Cmd 3) Set Part 2 Points (Cmd 65) Turn the System On with No Delay Turn the System On with No Exit Tone Turn the System On with Points Faulted (Force Arm) Bypass Points Date and Time (Cmd 45) Change Passcodes (Cmd 55) Change Other Passcodes (Cmd 56) Change Other s Passcode Level (Cmd 56) Add a Passcode (Cmd 56) Delete Passcodes (Cmd 58) Renew One-Time Passcodes (Cmd 53) Check System Troubles (Cmd 4) View Alarm Memory (Cmd 40) View System Trouble (Cmd 42) View Point Trouble (Cmd 48) System Test (Cmd 41) Copyright 2001 Radionics Page BĤ Walk Test (Cmd 44) Reset the System (Cmd 47) Turn Watch On/Off (Cmd 61) Select Watch Tone (Cmd 62) Select Watch Points (Cmd 63).39 Extend Auto On Time (Cmd 51) All Areas On (Cmd 80) All Areas Off (Cmd 81) Auto-Forward On/Off (Cmd 82) Remote Arming with Telephone, Area Remote Program (Cmd 43) Security System Limitations Fire Safety and Evacuation Maintenance and Service Power Failure How to Clean the Command Center Glossary Index B Copyright 2001 Radionicsĥ About This User s Guide This user s guide shows you how to use and maintain your security system. So if you have never worried about "dead devices" you might want to learn more about what they are and to to handle them, there are several posts on this forum.1 Security System User Guide for the LED Command CenterĢ MY SECURITY COMPANY IS: CALL BEFORE TEST: THIS SECURITY SYSTEM IS CONNECTED TO TELEPHONE NUMBER: THE SECURITY CONTROL PANEL IS CONNECTED TO THE PHONE JACK LOCATED: TRANSFORMER LOCATION: CIRCUIT BREAKER NUMBER: 46840B Copyright 2001 Radionicsģ Contents About This User s Guide. But when a node is really dead, sending data to that node might cause delays on your network. A global option can change this behavior.
If you have the "default polling," this happens at regular intervals so very likely *all* your mains powered devices will go "dead" after a power cut, requiring action to bring them back online. If your controller is on UPS and there is a power cut, the controller might send a command to a device and decide it is "dead". But often overlooked when people buy an UPS.
Although the HC2 has USB connectors, it does not support it. For instance, to do an automatic clean shutdown of your controller.
#Networx security command center power down code#
If the UPS has an HTTP interface, you might be able to write code (or find code) to get status of the UPS on your HC2. I'd say the load of the HC2 is < 20 W so if you put that number in an UPS calculator, you can find out the run time.
0 kommentar(er)
